Igis Mikrosfera Spray is a very light, fine-grained, ready-to-use, white, polymer-based finishing putty with a light filler, designed for use with a putty sprayer for interior applications. Easy to apply and level, with low water absorption and good vapor permeability; dries quickly.
Technical Specifications
Color: white
Maximum particle size: 0.1 mm
Coat thickness: 2…3 mm
Coverage: when applying a 1 mm coat, coverage is ~1 L/m²
Drying time: drying time depends on the substrate, coat thickness, temperature, relative humidity, etc. Drying time for a 1 mm layer (at +23°C and 50% relative humidity): can be sanded after 2–4 hours. A 1 mm layer dries completely after 24 hours and reaches its final strength after 28 days.
Application temperature: suitable air and surface temperatures are +8 to 25°C, with relative humidity of 35–80%. Avoid drafts, high temperatures, and low temperatures during application.
Application
: The putty is intended for leveling concrete, plaster, drywall, and other mineral surfaces prior to painting with water-based paints or hanging wallpaper. It adheres very well to substrate surfaces. It is elastic, easy to sand, dust-free, and forms a very smooth surface. Due to the putty’s low water absorption, surfaces do not need to be primed before painting. It allows for easy creation of textured surfaces. Improves the sound and thermal insulation of walls. Recommended for use as the final coat on the substrate before painting.
Substrate Preparation
The surface to be filled must be dry, free of loose material, firm, even, and clean. Old, flaking coatings and soft surfaces must be removed down to a solid substrate. To improve adhesion, previously painted smooth surfaces must be sanded and dust removed. Surfaces previously coated with chalk or lime must be thoroughly washed to remove all traces of previous coatings. Surfaces contaminated with mold or other microorganisms must be completely cleaned using a specialized cleaning agent. Fill the joints in gypsum board with a reinforcing joint compound. Prime dense, low-water-absorbing mineral surfaces or waterproof concrete surfaces with a special primer. Porous surfaces that absorb water heavily or unevenly (lightweight concrete, silicate bricks, gypsum boards, etc.) should be treated with a suitable deep-penetrating primer.
Filling
The filler is supplied ready for use. It must not be mixed with other materials. Before use and during application, the putty must be thoroughly mixed until a uniform consistency is achieved. When applying the putty, the air temperature must be above +8…10°C, with relative humidity between 35–80%. The putty can be applied to surfaces either manually with a putty knife or mechanically. For mechanical application, it is recommended to use an airless high-pressure sprayer. The first coat must be completely dry before applying the second coat. The maximum thickness of a single layer of putty is 2–3 mm. If MIKROSFERA lightweight fine-grained putty is used as the final layer, it is recommended to use MAKROSFERA lightweight coarse-grained putty as the first layer. Sand the dried fine-grained putty surface with 180–220-grit sandpaper. Carefully remove any sanding dust. Once the putty is completely dry, the surface can be painted with water-based decorative and finishing paints. Wash tools clean with water.
Storage
1 year from the date of manufacture indicated on the packaging. Store in the original, hermetically sealed container at a temperature of +5…30°C; protect from freezing, intense heat, and direct sunlight.
Safety Precautions
Keep out of reach of children. Avoid release into the environment. Wear protective gloves, protective clothing, safety goggles, and a respirator. IF ON SKIN: Wash thoroughly with plenty of water and soap. If skin irritation or a rash occurs: seek medical attention. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Rinse again. If eye irritation persists: seek medical attention. Contains 1,2-benzisothiazol-3(2H)-one. May cause an allergic reaction. Keep away from cold.
Waste Disposal
: Take empty, dry packaging to a packaging waste collection point for recycling; place dry product residues in a household waste container, and hand over liquid residues to a waste management company licensed to handle them. Information on waste management companies is available from your local government or the Environmental Board.