Eskaro WPC Refresher is a solvent-based maintenance product for wood-plastic composite (WPC) and plastic surfaces, for both outdoor and indoor use.
Refreshes the surface’s appearance
Enhances the surface’s natural color (wet-look effect)
Restores dull and worn surfaces while preserving their natural appearance
Protects against water, oil, grease, and other contaminants Ensures
long-lasting effectiveness and resistance to external influences
Absorbs into the surface without forming a film
Dries quickly
Easy to use
EU VOC content limit values: subcategory h 750 g/L, maximum VOC content in the ready-to-use product < 400 g/L.
Applications
: For the maintenance of decking boards, facade panels, and other products made from wood-polymer (WPC), bamboo-polymer (BPC) composite materials, and plastic products that may fade, become soiled, or be susceptible to weathering (garden furniture, boats, trim, etc.).
Surfaces
to Be Treated
New or old products and structures made of wood-polymer (WPC) and bamboo-polymer (BPC) composite materials or plastic.
Surface preparation
:
The surface to be treated must be thoroughly cleaned of dirt, grease, and dust. We recommend using TerraceClean to clean and wash the surfaces. It is not recommended to perform this work in hot weather, in direct sunlight, in strong winds, or during rain or fog. The surface must be clean and dry. WPC Refresh is ready to use and does not require dilution.
Application
: Stir the product thoroughly before use. The suitable air and surface temperature for application is +5…25°C, and the permissible relative humidity is up to 80%. Apply a thin layer of the product to the surface using a sponge, cloth, or spray bottle. Allow it to absorb for 10 minutes, then remove any excess product with a lint-free microfiber cloth. If necessary, repeat the treatment after 30–60 minutes. Do not apply too much product to the surface! WPC Refresher must be fully absorbed by the surface; it must not remain as a glossy film on the surface or accumulate in the grooves. After about 10 minutes, it is important to polish the surface with a dry, lint-free cloth. Polishing ensures an even and proper final result.
Maintenance
:
The treated surface is ready for use after 6 hours. Use a soft sponge or brush to wash the surface. For cleaning treated surfaces, we recommend using the TerraceClean cleaner (dilute according to the instructions) as well as neutral or mildly alkaline (pH 6–8) cleaning agents. Do not use cleaning agents containing abrasive or organic solvents, or rough sponges or brushes. After washing, rinse the surface with clean water and allow it to dry.
Tools
:
Sponge, deck pad, garden sprayer.
Cleaning
Tools
Clean tools with mineral spirits immediately after finishing work.
Safety Precautions
Caution! May be fatal if swallowed or if it enters the respiratory tract. Flammable liquid and vapor. Causes skin irritation. Contains hydrocarbons, C10–C13, n-alkanes, isoalkanes, cyclic compounds, <2% aromatic compounds. Wear protective gloves, protective clothing, safety goggles, and safety shoes. Wash skin thoroughly after handling. IF ON SKIN: Wash with plenty of water. Keep away from heat sources, hot surfaces, sparks, flames, and other sources of ignition. Do not smoke. In case of fire: use a foam extinguisher (AB), a dry chemical powder extinguisher (ABC), or a carbon dioxide extinguisher (BC) to extinguish the fire. If seeking medical attention, bring the product packaging or label with you. UFI: VD40-106X-S00A-KF9T Keep out of reach
of children Waste Management and Environmental Protection
Do not pour down the drain. Prevent release into the environment. Take unused paint to a waste collection point for recycling or reuse, or hand it over to a waste management company. Reusing the paint effectively reduces the environmental impact caused by using the product. Dried paint residues may be disposed of as regular waste. Clean and dry packaging must be taken to a packaging collection and recycling center. Information on collection points and waste management companies is available from local governments or the information portal http://www.kuhuviia.ee. For larger quantities, contact the Estonian Recycling Organization MTÜ (eto@eto.ee).
Storage
Conditions
Store in the tightly sealed original container at a temperature of +5…30°C. Protect from cold and direct sunlight.